Quilt Backing Calculator

A quilt backing must be bigger than the quilt top — longarm quilters need extra fabric to clamp, and the layers shift while quilting. Enter your quilt top size and the page adds the standard overhang, then works out the fabric yardage two ways: one single piece of wide fabric, and panels pieced from standard-width fabric with seams counted.

Default 4 inches on every side — the standard quilter's practice (see the FAQ). That is 8 inches added to both the width and the length. Longarm quilters often ask for 4 inches per side as a minimum.

Default ½ inch, the usual piecing seam allowance. Each seam joins two panels and takes the allowance from both sides, so one seam uses 2 × the allowance of fabric width in total.

Check before you cut. Yardage is rounded up to the nearest ⅛ yard and assumes straight, full-width panels with no directional print to match. Fabric widths vary slightly by bolt (a nominal 44-inch cotton is often 42–44 inches of usable width), directional prints and shrinkage can add to what you need, and your longarm quilter may ask for more than 4 inches of overhang — confirm their minimum before buying.

Formulas: backing width = top width + 2 × overhang; backing length = top length + 2 × overhang. Single piece (only when the fabric is at least as wide as the backing): yardage = backing length ÷ 36, rounded up to the nearest ⅛ yard. Pieced: panels = the smallest number n such that n × fabric width − (n − 1) × 2 × seam allowance ≥ backing width; yardage = panels × backing length ÷ 36, rounded up to the nearest ⅛ yard.

Frequently Asked Questions

Why does the backing need a 4-inch overhang on each side?

Because the three layers — top, batting, and backing — shift against each other while the quilt is being quilted, and a longarm machine clamps the backing to rollers, which needs extra fabric beyond the quilt top. Four inches per side (8 inches total on each dimension) is the standard minimum most longarm quilters ask for; some ask for more on large quilts, so check with your quilter before buying. The overhang is trimmed off after quilting.

How is the yardage computed?

First the backing size: add twice the overhang to each dimension of the quilt top (a 60 × 72 inch top with 4 inches of overhang needs a 68 × 80 inch backing). Then the fabric: if one width of your fabric covers the backing width, you need one panel as long as the backing — 80 inches ÷ 36 = 2.22 yards, rounded up to 2.25 yards. If the fabric is narrower, the backing is pieced from panels sewn side by side, and the yardage is the number of panels × the backing length ÷ 36, again rounded up to the nearest ⅛ yard.

How do seams affect the pieced yardage?

Each seam eats fabric width. With the standard ½-inch seam allowance, a seam takes ½ inch from each of the two panels it joins — 1 inch of width per seam in total. So two panels of 44-inch fabric give 44 + 44 − 1 = 87 inches of usable width, not 88. The calculator counts that: it finds the smallest number of panels whose usable width covers the backing width, then multiplies panels × backing length for the yardage.

When is one piece of wide fabric better than piecing?

Whenever the fabric is at least as wide as the backing: a single piece has no seam down the back and usually needs less yardage. Wide backing fabric (60 or 108 inches) is made for this. With standard 44-inch cotton, any backing wider than 44 inches must be pieced — for a 68-inch-wide backing that means 2 panels, and for a backing over 87 inches wide, 3 panels.

Why is the yardage rounded up to the nearest ⅛ yard?

Fabric is sold by the yard and cut in eighths, so the page rounds the exact figure up to the next cut you can actually buy. The exact figure is shown too, so you can see how much of the rounding is slack. If your print is directional or you plan to pre-wash (which shrinks cotton slightly), buy an extra ⅛–¼ yard on top.